Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
What are your ideas on Installing A Bathtub?
Installing a bathtub isn't exactly rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old tub is readily accessible, the task can relocate easily; if you need to open a wall surface to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to leave the old tub and also set in the brand-new one. Make certain you have certified yourself for the work and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is far better to take into consideration employing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will help you install a new bath tub in your bathroom if you have already purchased a brand-new bathtub and also do not need to change the plan of your previous water system pipelines.
Your devices as well as material list must consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be quite problematic as a result of the limited gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will originate from the pipes. When the supply pipelines have actually been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before moving on to fit the brand-new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the faucet as well as the sink. Safeguard the tap in place with the supplier offered backnut. Once the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be connected to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the called for position. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water system and also inspect all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling and securing around the bathtub must wait till the bathtub has actually been used at the very least once as this will resolve it into its final setting.
Getting ready for the Installment
First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, creating the water to pass through the wall surface between the bath as well as the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can split fairly early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly offered on the market. It is recommended to fit the floor tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that section was a good thing. So long as you appreciated our blog entry plz remember to share it. Thank-you for taking the time to read it.
Your search ends; experts here. Report this page